User Contributed MET/CAL PROCEDURE ============================================================================= INSTRUMENT: PM 5135 (Performance) Ver 1.0 DATE: 29-Oct-93 AUTHOR: User Contributed REVISION: 1.0 ADJUSTMENT THRESHOLD: 75% NUMBER OF TESTS: 48 NUMBER OF LINES: 287 CONFIGURATION: Fluke 8842A CONFIGURATION: Fluke PM 6654C CONFIGURATION: HP 8568A CONFIGURATION: Fluke 3365A ============================================================================= * 컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� * Source: Service Manual PM 5135 P/N: 9499 455 00511 @ 910721 * 컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� * TUR Configuration: * 컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� * When the T.U.R. is < 2:1, the source instrument, e.g. 5700A, must be * characterized and appropriate corrections entered in the correction file * (e.g. 5700.COR). Where T.U.R.'s are > 2:1 but < 4:1, the test tolerance * is reduced by root sum square (rss) techniques. * 컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� * This procedure is not executable in MET/CAL versions below ver. 2.00 * 컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� * Fluke make no warranty, expressed or implied, as to the fitness or * useability of this procedure. * 컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� * Main Procedure TESTS: Performance * 컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� * The following subprocedures are called from this main procedure: * 1 SUB PART1 PM 5135 (CALIBRATION) * TESTS/LINES : 26 / 189 #REV :1.0 * 컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� STEP FSC RANGE NOMINAL TOLERANCE MOD1 MOD2 3 4 CON 1.001 ASK- R N P F W 1.002 HEAD INTRODUCTION 1.003 DISP This procedure is intended to: 1.003 DISP - Check the instrument's specification. 1.003 DISP - Check the necessity of re-calibration. 1.003 DISP 1.003 DISP NOTE: 30 Minutes warmup is required before testing 1.004 HEAD {5.3.1.1 Frequency Range Limits} 1.005 DISP Setup UUT as follows: 1.005 DISP - FREQUENCY DIAL: MAX CCW, FREQUENCY: x10k 1.005 DISP - SWEEP: Off, WAVEFORM: Sine 1.005 DISP - ATTENUATION: All released, FREQUENCY OFFSET: Centered 1.005 DISP - DC OFFSET: Centered, AMPLITUDE: Centered 1.005 DISP 1.005 DISP Connect UUT RF output to the 6654 Channel A input. 1.006 IEEE [@6654]D MS1 F1[I][D100]X[I][D100]X[I] 1.007 MEM/ 1000000 1.008 MEMC 2.000MH -200% 2.001 DISP Setup UUT as follows: 2.001 DISP - FREQUENCY DIAL: MAX CW 2.002 IEEE [@6654]D MS1 F1[I][D100]X[I][D100]X[I] 2.003 MEMC 1000.0H +200% 3.001 HEAD {5.3.1.2 Frequency Setting Accuracy} 3.002 DISP Setup UUT as follows: 3.002 DISP - FREQUENCY DIAL: 200, FREQUENCY: x10k 3.003 IEEE [@6654]D MS1 F1[I][D100]X[I][D100]X[I] 3.004 MEM/ 1000000 3.005 MEMC 2.000MH 10% 4.001 DISP Setup UUT as follows: 4.001 DISP - FREQUENCY: x100 4.002 IEEE [@6654]D MS1 F1[I][D100]X[I][D100]X[I] 4.003 MEM/ 1000 4.004 MEMC 20.00KH 10% 5.001 DISP Setup UUT as follows: 5.001 DISP - FREQUENCY: x1 5.002 IEEE [@6654]D MS1 F1[I][D100]X[I][D100]X[I] 5.003 MEMC 200.0H 10% 6.001 DISP Setup UUT as follows: 6.001 DISP - FREQUENCY: x0.01 6.002 IEEE [@6654]D MS1 F1[I][D100]X[I][D100]X[I] 6.003 MEMC 2.000H 10% 7.001 DISP Setup UUT as follows: 7.001 DISP - FREQUENCY DIAL: 0.1, FREQUENCY: x10k 7.002 IEEE [@6654]D MS1 F3[I][D100]X[I][D100]X[I] 7.003 MEM* 1000000 7.004 MEMC 1000.0uS 10% 8.001 DISP Setup UUT as follows: 8.001 DISP - FREQUENCY: x100 8.002 IEEE [@6654]D MS1 F3[I][D100]X[I][D100]X[I] 8.003 MEM* 1000 8.004 MEMC 100.00mS 10% 9.001 DISP Setup UUT as follows: 9.001 DISP - FREQUENCY: x1 9.002 IEEE [@6654]D MS1 AT1 TL1 TL2 F3[I]X[I]X[I] 9.003 MEMC 10.000S 10% 10.001 HEAD {Fine Setting (FREQUENCY OFFSET)} 10.002 DISP Setup UUT as follows: 10.002 DISP - FREQUENCY DIAL: 20, FREQUENCY: x10k 10.002 DISP - FREQUENCY OFFSET: Centered (0 detent) 10.003 IEEE [@6654]D MS1 F1[I][D100]X[I][D100]X[I] 10.004 MEME >1 10.005 MATH MEM1=(MEM*1.20)/1E3 10.006 DISP - FREQ OFFSET: +20% (CW) 10.007 IEEE [@6654]MS1 X[I][D100]X[I][D100]X[I] 10.008 MATH MEM=MEM/1E3 10.009 MEMC KHz -200% +20%Offset 11.001 MEME <1 11.002 MATH MEM1=(MEM*.80)/1E3 11.003 DISP - FREQ OFFSET: -20% (CCW) 11.004 IEEE [@6654]MS1 X[I][D100]X[I][D100]X[I] 11.005 MATH MEM=MEM/1E3 11.006 MEMC KHz +200% -20%Offset 12.001 HEAD {5.3.2.1 Amplitude / Frequency Response (Flatness)} 12.002 DISP Setup UUT as follows: 12.002 DISP - FREQUENCY DIAL: 10, FREQUENCY: x100 12.002 DISP - FREQUENCY OFFSET: Centered (0 detent) 12.002 DISP - AMPLITUDE: 30Vpp (CW) 12.002 DISP 12.002 DISP Connect UUT RF output to the 8840 input 12.002 DISP with a 50 � termination. 12.003 8842 A 27.50D 10U 1kH 5Z N 2W 12.004 DISP Setup UUT as follows: 12.004 DISP - FREQUENCY DIAL: 20, FREQUENCY: x1 12.005 8842 A 00.00D 0.3U 20H 5Z C 2W 13.001 DISP - FREQUENCY DIAL: 50 13.002 8842 A 00.00D 0.3U 50H 5Z C 2W 14.001 DISP - FREQUENCY DIAL: 100 14.002 8842 A 00.00D 0.3U 100H 5Z C 2W 15.001 DISP - FREQUENCY DIAL: 200 15.002 8842 A 00.00D 0.3U 200H 5Z C 2W 16.001 DISP Setup UUT as follows: 16.002 DISP - FREQUENCY DIAL: 0.2, FREQUENCY X100 16.003 8842 A 00.00D 0.3U 20H 5Z C 2W 17.001 DISP - FREQUENCY DIAL: 1 17.002 8842 A 00.00D 0.3U 100H 5Z C 2W 18.001 DISP - FREQUENCY DIAL: 5 18.002 8842 A 00.00D 0.3U 500H 5Z C 2W 19.001 DISP - FREQUENCY DIAL: 20 19.002 8842 A 00.00D 0.3U 2kH 5Z C 2W 20.001 DISP - FREQUENCY DIAL: 100 20.002 8842 A 00.00D 0.3U 10kH 5Z C 2W 21.001 DISP - FREQUENCY DIAL: 200 21.002 8842 A 00.00D 0.3U 20kH 5Z C 2W 22.001 DISP Setup UUT as follows: 22.001 DISP - FREQUENCY DIAL: 0.1, FREQUENCY: x10k 22.002 8842 A 00.00D 0.3U 1kH 5Z C 2W 23.001 DISP - FREQUENCY DIAL: 0.2 23.002 8842 A 00.00D 0.3U 2kH 5Z C 2W 24.001 DISP - FREQUENCY DIAL: 1 24.002 8842 A 00.00D 0.3U 10kH 5Z C 2W 25.001 DISP - FREQUENCY DIAL: 5 25.002 8842 A 00.00D 0.3U 50kH 5Z C 2W 26.001 DISP - FREQUENCY DIAL: 10 26.002 8842 A 00.00D 0.3U 100kH 5Z C 2W 27.001 HEAD {5.3.2.2 Distortion (THD)} 27.002 IEEE [@8568][TERM LF]IP[D1000]I1,FA1KZ,FB25KZ,RL30DM[10] 27.003 DISP Setup UUT as follows: 27.003 DISP - FREQUENCY DIAL: 0.5, FREQUENCY: x10k 27.003 DISP - FREQUENCY OFFSET: Centered (0 detent) 27.003 DISP - AMPLITUDE: 15Vpp (Centered) 27.003 DISP 27.003 DISP Connect UUT RF output to 8568 Port 1 input (BNC). 27.004 IEEE [@8568]S2,TS,[D30]M2,E1,[D10]M3[10] 27.005 IEEE [@8568]FA7.5KZ,TS[D30],E1,MA[10][I] 27.006 MEMC 200 -25.0dBc +100% 500HzTHD 28.001 IEEE [@8568][TERM LF]S1,[D30]FA500HZ,FB5KZ[10] 28.002 DISP Setup UUT as follows: 28.002 DISP - FREQUENCY DIAL: 0.1 28.003 IEEE [@8568]S2,TS,[D30]M2,E1,[D10]M3[10] 28.004 IEEE [@8568]FA1.5KZ,TS[D30],E1,MA[10][I] 28.005 MEMC 200 -25.0dBc +100% 1KhzTHD 29.001 IEEE [@8568][TERM LF]S1,[D30]FA500HZ,FB5KZ[10] 29.002 DISP Setup UUT as follows: 29.002 DISP - FREQUENCY DIAL: 10, FREQUENCY: x100 29.003 IEEE [@8568]S2,TS,[D30]M2,E1,[D10]M3[10] 29.004 IEEE [@8568]FA1.5KZ,TS[D30],E1,MA[10][I] 29.005 MEMC 200 -40.0dBc +100% 1KhzTHD 30.001 IEEE [@8568]IP[10] 30.002 HEAD {5.3.3.1 Duty Cycle (Square Wave)} 30.003 DISP Setup UUT as follows: 30.003 DISP - FREQUENCY DIAL: 200, FREQUENCY: x10k 30.003 DISP - SWEEP: Off, WAVEFORM: Squarewave 30.003 DISP 30.003 DISP Connect UUT RF output to the 6654 Channel A input. 30.003 DISP 30.004 IEEE [@6654]D MS1 F1[I][GTL] 30.005 DISP Set the FREQUENCY DIAL for 2 +/-.01Mhz 30.006 IEEE [@6654]D MS1 F7[I][D100]X[I][D100]X[I] 30.007 MEM* 1000000000 30.008 MEMC 250.00nS 4% 31.001 IEEE [@6654]D MS1 F1[I][GTL] 31.002 DISP Setup UUT as follows: 31.002 DISP - FREQUENCY DIAL: 0.1, FREQUENCY: x10k 31.002 DISP 31.002 DISP Set the FREQUENCY DIAL for 1 +/-.01Khz 31.003 IEEE [@6654]D MS1 F7[I][D100]X[I][D100]X[I] 31.004 MEM* 1000000 31.005 MEMC 500.00uS 4% 32.001 IEEE [@6654]D MS1 F1[I][GTL] 32.002 DISP Setup UUT as follows: 32.002 DISP - FREQUENCY DIAL: 200, FREQUENCY: x100 32.002 DISP 32.002 DISP Set the FREQUENCY DIAL for 20 +/-.01Khz 32.003 IEEE [@6654]D MS1 F7[I][D100]X[I][D100]X[I] 32.004 MEM* 1000000 32.005 MEMC 25.000uS 4% 33.001 IEEE [@6654]D MS1 F1[I][GTL] 33.002 DISP Setup UUT as follows: 33.002 DISP - FREQUENCY DIAL: 0.1 33.002 DISP 33.002 DISP Set the FREQUENCY DIAL for 10 +/-.01Hz 33.003 IEEE [@6654]D MS1 F7[I][D100]X[I][D100]X[I] 33.004 MEM* 1000 33.005 MEMC 50.000mS 4% 34.001 IEEE [@6654]D MS1 F1[I][GTL] 34.002 DISP Setup UUT as follows: 34.002 DISP - FREQUENCY DIAL: 200, FREQUENCY: x1 34.002 DISP 34.002 DISP Set the FREQUENCY DIAL for 200 +/-.01Hz 34.003 IEEE [@6654]D MS1 F7[I][D100]X[I][D100]X[I] 34.004 MEM* 1000 34.005 MEMC 2.5000mS 4% 35.001 IEEE [@6654]D MS1 F1[I][GTL] 35.002 DISP Setup UUT as follows: 35.002 DISP - FREQUENCY DIAL: 200, FREQUENCY: x.01 35.002 DISP 35.002 DISP Set the FREQUENCY DIAL for 2 +/-.01Hz 35.003 IEEE [@6654]D MS1 TL1 F7[I][D100]X[I][D100]X[I] 35.004 MEM* 1000 35.005 MEMC 250.00mS 4% 36.001 HEAD {5.3.3.2 Rise and Fall Times} 36.002 IEEE [@6654]D MS1 F9[I][GTL] 36.003 DISP Setup UUT as follows: 36.003 DISP - FREQUENCY DIAL: 200, FREQUENCY: x10k 36.003 DISP - WAVEFORM: Squarewave, AMPLITUDE: 30 Vpp (CW) 36.003 DISP 36.003 DISP Connect UUT RF output to the 6654 Channel A input. 36.004 IEEE [@6654]D MS1 AS0 F9[I]X[I]X[I] 36.005 MEM* 1000000000 36.006 MEMC 70.000nS +100% RiseTime 37.001 IEEE [@6654]D MS1 AS1 F9[I][D100]X[I][D100]X[I] 37.002 MEM* 1000000000 37.003 MEMC 70.000nS +100% FallTime 38.001 DISP Setup UUT as follows: 38.001 DISP - FREQUENCY: x100 38.002 IEEE [@6654]D MS1 AS0 F9[I]X[I]X[I] 38.003 MEM* 1000000000 38.004 MEMC 70.000nS +100% RiseTime 39.001 IEEE [@6654]D MS1 AS1 F9[I][D100]X[I][D100]X[I] 39.002 MEM* 1000000000 39.003 MEMC 70.000nS +100% FallTime 40.001 DISP Setup UUT as follows: 40.001 DISP - FREQUENCY: x10k, AMPLITUDE: 3 Vpp (CCW) 40.002 IEEE [@6654]D MS1 AS0 F9[I]X[I]X[I] 40.003 MEM* 1000000000 40.004 MEMC 70.000nS +100% RiseTime 41.001 IEEE [@6654]D MS1 AS1 F9[I][D100]X[I][D100]X[I] 41.002 MEM* 1000000000 41.003 MEMC 70.000nS +100% FallTime 42.001 DISP Setup UUT as follows: 42.001 DISP - FREQUENCY: x100 42.002 IEEE [@6654]D MS1 AS0 F9[I]X[I]X[I] 42.003 MEM* 1000000000 42.004 MEMC 70.000nS +100% RiseTime 43.001 IEEE [@6654]D MS1 AS1 F9[I][D100]X[I][D100]X[I] 43.002 MEM* 1000000000 43.003 MEMC 70.000nS +100% FallTime 44.001 HEAD {5.3.3.3 Overshoot and Ringing} 44.002 DISP Setup UUT as follows: 44.002 DISP - FREQUENCY DIAL: 200, FREQUENCY: x10k 44.002 DISP - WAVEFORM: Squarewave, AMPLITUDE: 30 Vpp (CW) 44.002 DISP 44.002 DISP Connect UUT RF output to the 3365 Channel A input 44.002 DISP with a 50 � Termination. 44.003 IEEE [@3365][SPL]SET AUT,VER A,ATT 2E+00[10] 44.003 IEEE [@3365]HOR MTB,TIM .1E-06[10] 44.003 IEEE [@3365]MSC AUX,MEM OFF[10][GTL] 44.004 EVAL Is The {Overshoot and ringing < 300 mVpp (2Mhz, 30Vpp) } 45.001 DISP - FREQUENCY: x100 45.002 IEEE [@3365]HOR MTB,TIM 10E-06[10][GTL] 45.003 EVAL Is The {Overshoot and ringing < 300 mVpp (20Khz, 30Vpp) } 46.001 DISP Setup UUT as follows: 46.001 DISP - FREQUENCY: x10k, AMPLITIDE: 3 Vpp (CCW) 46.002 IEEE [@3365]VER A,ATT .2E+00[10] 46.002 IEEE [@3365]HOR MTB,TIM .1E-06[10][GTL] 46.003 EVAL Is The {Overshoot and ringing < 30 mVpp (2Mhz, 3Vpp) } 47.001 DISP - FREQUENCY: x100 47.002 IEEE [@3365]HOR MTB,TIM 10E-06[10][GTL] 47.003 EVAL Is The {Overshoot and ringing < 30 mVpp (20Khz, 3Vpp) } 48.001 CALL Sub Part1 PM 5135 (Performance) 48.002 END